Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Clovis Homeowners Choose Trane Air Duct Cleaning
We’re an independent Trane air duct cleaning and repair provider offering Trane service in Clovis and the surrounding San Joaquin Valley. What sets our Trane work apart is simple: we don’t just vacuum ducts, we open the system, video-scope the actual Trane components, and clean what’s actually fouling your airflow. The duct doesn’t lie – pull it open and you know exactly what’s been circulating through your house. Call (855) 661-0630 for a free estimate from a crew that knows Trane equipment from the inside out.
Duct Cleaning Clovis is not affiliated with or authorized by Trane. We’re an independent service provider, which means we repair what needs repairing and clean what needs cleaning without any pressure to sell replacement equipment. As owner Noel Drummond puts it, he grew up off Herndon Avenue and has spent the better part of two decades pulling debris, dust, and the occasional rodent nest out of residential duct systems across Clovis. The Trane units in this valley face conditions most equipment never sees: month after month of 100°F-plus attic heat, fine agricultural dust, and smoke that settles into the inversion layer every fall. That grit doesn’t stay outside. It loads your blower wheel, mats your coil, and gets drawn through return leaks. We fix all of it.
Why Trust Duct Cleaning Clovis for Your Trane Air Duct Cleaning?
We’ve opened up duct systems behind Trane XR, XLi, and XV equipment across Clovis for years. That hands-on time means we know exactly where Trane components collect debris and how that debris changes system behavior. A Trane XV variable-speed air handler doesn’t get dirty the way a basic single-stage unit does. The blower wheel runs constantly at low speed, which means fine dust and pet hair pack onto the wheel blades gradually. By the time you notice rooms are uneven or the system short-cycles, the wheel is often carrying enough weight to throw static pressure out of spec. We recognize that pattern because we see it in Clovis homes throughout the year.
Noel founded Duct Cleaning Clovis on a straightforward principle: use negative-pressure cleaning with truck-mounted and professional-grade equipment rather than the hand-vac shortcuts that pass for service at a lot of operations. He picked up his HVAC fundamentals at Fresno City College, where a sheet-metal and air distribution course convinced him that duct work was the most overlooked and most consequential piece of any home’s mechanical system. We also provide Trane in Fresno and surrounding areas. His daughter has asthma, and that’s the real reason he takes air quality seriously. It’s not a marketing angle. It’s the reason he got into this trade in the first place. Our Trane work reflects that same standard: video inspection before any cleaning, a clean scope of what needs repair, and no upsells on equipment you don’t need.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Trane Air Duct Cleaning Problems We Fix in Clovis
- Trane XV variable-speed blower wheels packed with fine dust and pet hair. The blower wheel on a Trane XV air handler runs nearly continuously at low speed. That’s great for efficiency, but it means airborne particulate gets pulled across the wheel blades for thousands of hours. In Clovis, where summer air is dry and gritty and the system runs four to six months nonstop, that wheel loads up. Result: reduced CFM, static-pressure fault codes, and uneven cooling. We pull the blower assembly, remove the wheel, clean it properly, and reinstall with the correct torque.
- Trane cased evaporator coils with a dust mat on the upstream face. Trane’s all-aluminum spine-fin coils are efficient, but their fins are tightly packed and trap dust aggressively. The coil sits upstream of the blower in most configurations, which means all that return air hits it first. In Clovis, fine agricultural dust and valley particulate form a blanket across the upstream face within a few seasons. Airflow drops, the coil temperature falls, and ice can form. We clean the coil with coil-specific methods that don’t crush the delicate spine-fin profile.
- Sagging or loose flex return runs pulling attic air into the system. Clovis tract housing built from the 1990s onward typically uses flexible Mylar duct run through hot attics. Summer attic temperatures in this area routinely exceed 130°F. Over time, the flex duct’s inner liner sags, the outer jacket tears, and connections at the plenum loosen. Now your Trane system is pulling 130°F attic air straight into the return. Rooms get dusty, coil loads climb, and the system runs longer just to hold temperature. We find and seal these return leaks with mastic-rated sealants that actually hold.
- Trane horizontal attic air handlers with condensate-pan dust crust and blower heat soak. Horizontal Trane air handlers installed in Clovis attics sit in the worst thermal environment in the house. The condensate pan collects not just water but airborne dust that settles into the pan and forms a crust. That crust holds moisture, which feeds mold and blocks proper drainage. At the same time, blower motors heat-soak in the attic ambient. When return airflow is restricted by dirty ducts, the motor runs hotter and the whole cabinet bakes. We clean the pan, clear the drain line, and restore the airflow that protects your blower.
- Disconnected flex duct at plenum boots causing whole-room dust and heat. It’s common enough in Clovis that we expect it on a certain age of install: a flex run has pulled loose from its boot, leaving a room partially disconnected from the system. The room never cools right, and whatever is in the attic gets pulled into the duct. Sometimes homeowners call us for “dusty vents in one room” when the real problem is a disconnected run. Our video scope finds it in under a minute.
Trane Parts & Our Repair-vs-Replace Approach
We use OEM Trane-compatible filters, gaskets, and mastic-rated sealants where fitment matters. For flex duct and insulation replacement, we use quality aftermarket materials where the spec is equivalent. We don’t cut corners on the things that determine whether your Trane system runs clean and sealed. On a Trane system, if the coil and blower are sound, we clean and seal rather than push replacement. If the heat exchanger or coil is compromised, we tell you straight and show you the evidence on camera. That’s the standard Noel runs his crews by.
A typical repair decision sounds like this: a Trane XR system with a clean coil, healthy blower, and a sagging return run doesn’t need a new air handler. It needs the return run repaired, the plenum sealed, and the coil cleaned. If the coil is split or the heat exchanger on an S-Series furnace is cracked, replacement is the honest call. Call (855) 661-0630, and we’ll walk you through what we find after a full inspection.
Our Trane Service Process – Step by Step
- 1
Diagnosis and video inspection. We start by running your Trane system and taking static-pressure and temperature readings. Then we open the blower door and coil access panel and run a video scope through the return and supply runs. You get a real look at what’s inside, not a sales pitch.
- 2
Repair before cleaning. If we find a disconnected boot, a sagging return run, or a crushed flex duct, we fix it first. Cleaning a duct system that’s still leaking or disconnected is wasted effort.
- 3
Coil and blower cleaning. The evaporator coil and blower wheel are where Trane systems actually load up. We clean both with methods matched to the all-aluminum spine-fin coil profile and the variable-speed blower assembly, then reassemble with proper torque and gaskets.
- 4
Negative-pressure cleaning with sealing. Using professional-grade negative-pressure equipment, we clean the full duct run and then mastic-seal all accessible joints, boots, and return connections. The goal is a sealed, clean system, not just swept ducts.
- 5
Post-service testing. We re-check static pressure, verify CFM output, and run the system through a full cycle. If your Trane system had low airflow before, the difference should show in the gauge readings, not just on a sales sheet.
See the difference
Before
After
Before
After
Before
AfterTrane Products We Service & Install in Clovis
Our crews work on Trane XR series split systems, XLi series units, XV variable-speed air handlers, and S-Series furnaces (S9V2, S8X2) with their matching cased coils. That covers the bulk of Trane residential equipment installed in Clovis homes from the 1990s through the 2010s. We also work behind Trane systems paired with Honeywell and Aprilaire whole-home filtration. If you have a Trane air handler with a Honeywell media cabinet or an Aprilaire filter housing, we clean the duct work and the filtration interface so the whole IAQ setup works, not just a standalone duct run. For heat-pump and air-conditioner coil cleaning, we stock the common Trane-compatible access gaskets and mastic sealants we use daily, so a typical service call doesn’t mean waiting on an order.
We Also Service These Brands
We’re not single-brand dependent. Alongside Trane, we clean and repair duct systems behind Lennox and Carrier equipment, and we work with residential forced-air setups regardless of the equipment badge. If your ducts are dirty, the equipment brand matters for the service particulars, but the duct work itself is our specialty. One call at (855) 661-0630 covers the full scope, no second contractor needed.
FAQs – Trane Air Duct Cleaning Service in Clovis
No. We’re an independent provider and not affiliated with or authorized by Trane. What that means in practice is we don’t answer to a manufacturer’s sales targets. We answer to the condition of your duct system and the readings on our gauges. That independence is why we’re comfortable telling you when a Trane coil is fine to clean rather than replace, or when a heat exchanger is genuinely done and shouldn’t be patched.
We use OEM Trane-compatible filters, gaskets, and mastic-rated sealants where the fitment matters. For flex duct, insulation, and general duct-repair materials, we use quality aftermarket products where the spec is equivalent. If a part has to fit a Trane cabinet or blower assembly exactly, we don’t gamble with cheap generics. If the part is generic duct material, we choose the right spec and don’t pay extra for a label.
A standard Trane system cleaning with coil and blower service runs four to six hours for a typical Clovis tract home. If we find return leaks, disconnected runs, or need to repair flex duct, that adds time. We give you a clear scope before we start and a flat price per system agreed in advance. Call (855) 661-0630 for a time estimate on your specific system.
We service and repair duct systems behind Trane XR series, XLi series, and XV variable-speed air handlers, plus S-Series furnaces (S9V2 and S8X2) with matching cased coils. If your Trane equipment is older or less common, give us the model number and we’ll confirm coverage before scheduling. Chances are we’ve worked on that unit or its near relative in Clovis at some point.
No. Duct cleaning done properly doesn’t void a Trane equipment warranty. What can cause warranty problems is damage from improper cleaning: crushed flex duct, broken coil fins, or blower assemblies reinstalled incorrectly. That’s why we video-inspect first, use coil-safe methods on Trane spine-fin coils, and torque blower assemblies back to spec. If your system has an active warranty, we work within the practices that keep it intact.
The Trane XV air handler runs its blower nearly continuously at low speed for efficiency. A single-stage blower cycles on and off, so dust settles when the air stops moving. The variable-speed blower keeps that dust airborne and pulls it across the blower wheel hour after hour, month after month. In Clovis and nearby Tarpey Village, where the summer AC season stretches for months and the air carries fine valley particulate, that wheel packs up faster than most homeowners expect. Add a return leak pulling attic air, and the dust load doubles.
Yes, and it’s one of the most common issues we diagnose in Clovis. A dirty return duct restricts airflow across the evaporator coil, and when the coil doesn’t get enough warm air moving over it, the refrigerant temperature drops below freezing. The coil ices over, airflow drops further, and the system either short-cycles or stops cooling altogether. A dirty filter alone can do it, but a duct system packed with fine valley dust is a slower, more persistent version of the same problem. If your Trane coil is freezing, call (855) 661-0630 and we’ll inspect the whole return path, not just swap the filter.
Yes. Trane’s spine-fin coils are built differently from standard plate-fin coils. The fins are fine, tightly packed, and easy to crush with aggressive brushing or high-pressure washing. We use coil-specific cleaning methods that loosen and flush the debris without bending or matting the spine-fin profile. A coil that’s cleaned roughly might look better than it did, but its airflow is still compromised. We clean it right and then verify airflow before we leave.
Yes, and it matters in Clovis specifically. A horizontal Trane air handler in a 130°F-plus attic is already working in the worst thermal environment we see in this valley, and homeowners needing Trane repair in Sunnyside face the same challenges. The duct work runs through that same hot space, which means the flex liner ages faster, connections pull loose sooner, and the whole return side is more likely to be pulling hot attic air. We inspect attic runs with that in mind: looking for sag, crush, disconnect, and return leakage before we ever hook up the cleaning equipment. Once the leaks are sealed, the cleaning pulls only from inside the house, which is the point of a sealed system.
Trane air duct cleaning in Clovis typically runs $450 to $850 for a complete system cleaning with coil and blower service on a standard single-family home. Larger homes, multiple systems, or repair work on disconnected flex runs and return leaks add to that. We quote one flat price per system before work starts, so you won’t get a cheap per-vent teaser that balloons once the van is in your driveway. Call (855) 661-0630 for an exact quote on your Trane setup. Estimates are free.
Book Your Trane Service in Clovis, CA
If your Trane system is short-cycling, running dusty, or the upstairs rooms in your Clovis home haven’t cooled right in months, call Duct Cleaning Clovis at (855) 661-0630. We’ll schedule a video inspection, show you what’s actually in your ducts, and quote one flat price before any work starts. Own a Trane. Trust the people who know how it acts in this valley.
Written by Noel Drummond, Owner at Duct Cleaning Clovis, serving Clovis and the San Joaquin Valley since he started pulling debris out of residential duct systems fourteen years ago.