Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Why Clovis Homeowners Choose Carrier Air Duct Cleaning
Duct Cleaning Clovis provides independent Carrier air duct cleaning, evaporator coil cleaning, and blower cleaning service in Clovis, CA. If you own a Carrier system and the airflow has gone weak, the registers smell musty, or rooms run uneven – the problem is almost never the thermostat. It’s what’s packed inside the ducts, the coil, and the blower wheel. We pull those components, clean them with professional-grade Rotobrush and Nikro equipment, and repair the flex-duct failures Carrier systems in Clovis attics are prone to. One call: (855) 661-0630.
We are an independent Carrier service in Clovis. We’re not affiliated with, authorized by, or sponsored by Carrier Corporation. That’s actually the point – we see the real-world failure modes on Carrier systems in Clovis tract homes and older ranch neighborhoods, not the lab conditions in a spec sheet. Our technicians have pulled apart Carrier Comfort series air handlers, Infinity variable-speed systems, and 58-series furnaces across this valley for the better part of two decades. We know what a Clovis attic does to Carrier flex duct in August.
Why Trust Duct Cleaning Clovis for Your Carrier Air Duct Cleaning?
Carrier builds a solid piece of equipment. What happens to it after ten years in a Clovis attic is a different story. The attic in a Clovis subdivision hits 130°F-plus on an August afternoon, and those flexible Mylar duct runs bake, sag, and eventually separate at the plenum collar. The blower wheel loads up with a fine valley grit that passes right through the filter. The cased evaporator coil on an upflow Carrier furnace becomes a dust mat on the incoming face. These are the conditions our techs work in every day.
Noel Drummond, owner at Duct Cleaning Clovis, learned the trade fundamentals at Fresno City College, where a sheet-metal and air distribution course made it clear that ducts were the most overlooked part of any mechanical system. He’s spent nearly two decades since pulling debris, mold clusters, and the occasional rodent nest out of residential duct systems across the San Joaquin Valley. His daughter has asthma, which is why he got into this work and why he treats air quality in a home as something you fix, not something you upsell. The duct doesn’t lie – pull it open and you know exactly what’s been circulating through your house.
When we service a Carrier system, we’re not running a hand-held vacuum through a register and calling it a day. We use Rotobrush brush-contact extraction and Nikro HEPA-filtered negative-air systems – the same class of equipment restoration and remediation crews run after contamination jobs. We clean the blower assembly, the evaporator coil, the supply trunks, and the return side. Then we repair what’s wrong: reseal separated takeoffs, replace crushed flex runs, and reconnect ducts that have pulled loose from plenum boots.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Common Carrier Air Duct Cleaning Problems We Fix in Clovis
- Infinity variable-speed air handler blower faults and weak airflow. The ECM blower module on a Carrier Infinity air handler communicates with the system, but a dust-caked blower wheel throws off its load sensing and can lock the motor into a fault state. In Clovis, months of dry, dust-laden air push fine particulate through the filter and onto the blower wheel. We pull the blower assembly, clean each vane, reset the module, and verify airflow with a static pressure reading. Most “ECM module failed” calls we get are actually dirty blower issues.
- Cased evaporator coil dust loading on Carrier upflow furnaces. The cased coil sits above or below the furnace and traps dust, pet hair, and grease on the underside – the incoming face. Once that mat thickens, return air chokes, static pressure climbs, and the coil can ice over. We see this constantly on Carrier Comfort and Performance series systems in Clovis homes with pets. Our Nikro HEPA system and coil-cleaning process strip that layer without bending fins or pushing debris into the supply side.
- Flex-duct separation at the plenum collar. Factory flex runs on Carrier systems in Clovis attics hang in extreme heat. The zip ties or tape at the collar dry out, the inner liner tears, and the flex pulls loose. That means conditioned air is dumping into the attic while the rooms starve. We find this in newer master-planned Clovis subdivisions all the time. The fix is sealing, re-securing, and insulating – and then cleaning the dust that got drawn into the system while it was open.
- Dust and moisture in the condensate pan and secondary heat exchanger area on older 58-series Carrier furnaces. Older Carrier 58-series furnaces still run in established Clovis neighborhoods near Old Town. Over decades, the internal pan and heat exchanger areas trap dust, combustion byproduct residue, and moisture, producing a musty smell that travels through the supply ducts on startup. Cleaning the blower and coil matters, but so does clearing those internal surfaces and ensuring condensate is draining properly.
- Uneven rooms and dusty supply registers from crushed or kinked attic flex. In Clovis ranch homes and newer tract builds, flex duct gets flattened by stored boxes, walked-on runs, or framing contact. A kinked Carrier supply run can cut airflow to a back bedroom by half. We inspect the full trunk and branch layout, remove crush points, and where a run has collapsed, we replace it. That’s the repair half of what we do – most “clean only” companies won’t touch it.
Carrier Parts & Our Repair-vs-Replace Approach
We stock and specify Carrier-compatible OEM parts where control communication and fit matter. That means ECM blower modules, limit switches, and coil components sourced to match your specific Carrier model. For flex duct, mastic, insulation, and collar hardware, we run quality aftermarket material that meets or exceeds what builders originally installed – it performs identically without the manufacturer markup.
On older Carrier equipment, we’re honest about the call. If your 20-year-old Carrier furnace has a rusted secondary heat exchanger or a failing ECM module, cleaning the ducts isn’t the first problem to solve. But it may be the cheaper one to fix correctly while you decide on equipment replacement. We’ll tell you when a coil and blower cleaning restores performance, and we’ll tell you when further money into the existing equipment is a losing bet. Call (855) 661-0630 if you want a straight answer – we inspect before we quote.
Our Carrier Service Process – Step by Step
- 1
Diagnosis and pressure check. We measure static pressure across the system and inspect the blower wheel, coil face, and accessible flex runs. If a Carrier Infinity system is throwing a code, we note it and work through the airflow side before recommending any module replacement.
- 2
Cleaning with Rotobrush and Nikro. We run brush-contact extraction through the supply and return runs, pulling loosened debris under negative pressure through a HEPA-filtered Nikro system. The coil, blower assembly, and drain pan get cleaned separately, not bypassed.
- 3
Repairs and sealing. Here’s where we differ from a vended-clean-only outfit in Clovis. We reseal separated takeoffs at the Carrier plenum, replace crushed flex sections, re-secure collars, and repair what’s actually causing the airflow loss or dust intrusion.
- 4
Verification and video. After cleaning and repairs, we recheck static pressure, confirm airflow at key registers, and show you before-and-after images of your own ducts. We also evaluate how your system integrates with any Honeywell or Aprilaire whole-home filtration equipment – cleaning the ducts while ignoring the filtration side is half a job.
- 5
Post-service guidance. You get a plain-language summary of what we found and what we fixed. No binder, no scare tactics. Just what was wrong, what we did, and what to watch for in a Clovis attic environment.
See the difference
Before
After
Before
After
Before
AfterCarrier Products We Service & Install in Clovis
We work on Carrier residential and light-commercial air systems across the full lineup: Carrier Comfort and Performance series gas furnace-and-coil combinations common in Clovis tract homes; Carrier Infinity variable-speed air handlers with communicating controls; Carrier 24ACC6 and 24ACB7-style condensing units paired with slab or cased evaporator coils; and older Carrier WeatherMaker units and 58-series furnaces still running in established Clovis neighborhoods. We also service and clean the duct runs tied to those systems. If you have a Carrier model we haven’t listed, call us – if it moves air in the Carrier in Fresno and Clovis Valley, we’ve worked on it.
We Also Service These Brands
Plenty of Clovis homes run Lennox or Trane equipment, and we service those systems with the same full-scope approach: cleaning, repair, and dryer vent work in one visit. We’re not a single-brand shop. We’re a duct and airflow specialist that works across the brands people actually have in this valley.
FAQs – Carrier Air Duct Cleaning Service in Clovis
No. Duct Cleaning Clovis is an independent service provider. We are not affiliated with, authorized by, or sponsored by Carrier Corporation. What we are is experienced with Carrier equipment in Clovis attics, from builder-grade Comfort series systems to Infinity variable-speed air handlers. Independence means we recommend what the system actually needs, not what a manufacturer program tells us to sell. Call (855) 661-0630 for an evaluation.
Yes, and it’s more common than a true module failure. A dust-caked blower wheel on an Infinity variable-speed air handler changes the load the ECM module senses, and the controller can lock out with a fault code. The fix often starts with pulling and cleaning the blower assembly, then clearing the code and verifying airflow. We handle that in Clovis regularly. If the module itself has failed, we’ll tell you after we’ve eliminated the airflow causes. Call (855) 661-0630 to schedule a diagnostic.
In one way: the blower wheel tolerates far less buildup. A variable-speed ECM motor ramps airflow precisely, and when the wheel loads up with dust, the motor draws more current and can throw codes. Standard single-stage units just get loud and weak. Both need the same thorough Rotobrush and Nikro extraction we run, but on a variable-speed Carrier we’re paying extra attention to blower wheel cleanliness and static pressure after the job.
The usual culprit in Clovis is a combination of dust and moisture on the evaporator coil and in the drain pan, sometimes with secondary heat exchanger buildup on older 58-series furnaces. During cooling season, condensation wets the dust on the coil, and that biological film produces the musty smell that pushes through the supply ducts. Cleaning the coil, blower assembly, and pan removes the source. Sealing any intake near the attic or crawlspace keeps it from coming back.
Yes. Factory flex runs in Clovis attics sag, kink, tear, and separate at the plenum collar constantly – the heat and dry air do real damage. We inspect each run, clean what’s salvageable, and replace only the sections that are crushed, torn, or collapsed. The goal is full airflow restored to every register, not a wholesale re-duct job you don’t need. That’s the repair side of what we do, and it’s why we handle cleaning and repair as one company: no subcontracting, no second call.
Full-system Carrier air duct cleaning in Clovis – including blower assembly, evaporator coil, supply trunks, and return side – typically runs $350 to $800 for a standard single-story home, depending on system size, the number of returns, and how much coil and blower cleaning is required. Two-story homes with dual systems or heavily loaded coils can run higher. We quote one flat price per system before work starts, not a per-vent number that inflates once we arrive. Call (855) 661-0630 for an exact quote on your Carrier system – estimates are free and based on a real inspection.
Book Your Carrier Service in Clovis, CA
If your Carrier system is moving weak air, blowing dust, or smelling like the attic it runs through, let’s pull it apart and see what’s actually in there. Call (855) 661-0630 for a free estimate. We’ll inspect, give you a flat price, and tell you honestly what needs cleaning and what needs repair. One company, start to finish.
Written by Noel Drummond, Owner at Duct Cleaning Clovis, serving Clovis and the San Joaquin Valley.